Jump to content


Standard Member
  • Content count

  • Joined

  • Last visited

Community Reputation

0 Neutral

About ColS15

  • Rank
    Standard Member

General Info

  • Location
    Australia NSW
  • Car Type
    Nissan Silvia
  • Car Model
  1. sr20 cast / ebay sumps

    Ive had a tight arse ebay one for a couple of years now with no problems. . I think i payed $70. I did drill out and helicoll the sump plug thread, also hand filed the sump plug mating surface to make it smooth and flat. A liberal dose of sealant to sump surface during install and I've never had a leak.
  2. Thanks OLDIE. I'm prett sure his are the generic one's off ebay, the same ones everyone seems to sell except GCG who want $200 for theirs.
  3. I'll soon be building a v-band dump pipe. Anyone know of a good brand v-band flange and clamp kit? Or does everyone run with the e-bay specials?
  4. I hope internal gates are the go with efr series turbochargers, garret type/style are better with external.
  5. Lossing Power Under Full Throttle

    Yes, you can go a step colder at that boost. Plugs are Bkr7e
  6. Gasket should be .5 to 1mm bigger than poiston/bore size. Look at the blown gasket and see if you can work out where the leak occured. Is the fire ring marked?
  7. efr 6258 t4

    It's the external twin gate manifold only, I need the internal. $500 postage from the US to Australia for a manifold.. has trump ruined their postage system.
  8. efr 6258 t4

    Thanks bling, I'll have a look.
  9. Removing camshafts

    Yes, Once the tensioner is removed you can either - Remove the bolts from the cam gears and take them out. Remove the cam caps and take the cams out with the gears still attached. If you have rocker arm stoppers fited you need to remove the whole cam and gear then separate them. There is a hex drive on the cam behind where the gears are fitted, it can't be gotten to while the stoppers are fitted (atleast on the stoppers I've come across).
  10. efr 6258 t4

    What size cc short injectors (33.6mm o-ring to o-ring) are best suited to running e85 and 300rwkw with some head room? Are the stainless body ones short?
  11. Removing camshafts

    Chain stays in while cams come out. Hook a bungee chord onto the chain (between cams) and connnect it one of the holes in the structural support on the underside of the bonnet. Then remove cam caps and then cams.
  12. efr 6258 t4

    I just bought a 6758 t4 this afternon for $2200 postage included. That's cheaper than anywhere else i could find, although it is a german based company. I have a e-mail address for the employee i contacted, he speaks English. Pm me if you require it. http://www.gt-turbosystems.com/
  13. efr 6258 t4

    6258 t25 http://gcg.com.au/petrol-performance/performance-1/borg-warner-turbochargers/borg-warner-efr6258-turbocharger-t25-v-band-detail Or Performanceworld1 has them on ebay for $2500 delivered May be cheaper to buy+get delivered from the states.
  14. efr 6258 t4

    Thanks Tom... 6758 t4 is defiantly the way I'm going to go. Anyone interested in purchasing a slightly used gt2871r? Ha ha....
  15. efr 6258 t4

    No 7163 for me. . Or ve head, I'm still running the standard 6mt. I figure if it gets to the point where I'm going to do a head swap or change from the 6mt I'll sell the car, I'll buy another skyline. Thanks for the info The big fist, i just had a look at Sinco's site. I think I'll go down the 6758 and flex fuel route. What size bosch injectors are the stainless ones that don't clog up?